Assembling the BitFenix Ronin

There are a few reasons to go with larger cases if you're assembling a full ATX system: a larger ATX case will typically offer support for larger fan sizes (which can move more air at lower fan speeds and thus run at lower noise levels), and it's liable to be less cramped when you're working on it. That's not to say the BitFenix Ronin is particularly cramped, but it's definitely a change when you consider the last case I assembled was the NZXT Phantom 530.

Installing the motherboard could've been a little more convenient; there's no alignment stud like Corsair typically includes, and only two standoffs come preinstalled in the tray. BitFenix at least includes a socket with a phillips head to make tightening the standoffs easier. I've taken to connecting SATA leads and case headers at this step as the dual GeForce GTX 580s hang over the SATA ports on our test board, and found that the routing holes in the motherboard tray are just a little on the small side.

Where I think BitFenix made a really brilliant design choice is in the toolless drive trays. Typically there have been two ways to go about designing these: bendable plastic ones that snap around the 3.5" drive and don't feel secure but don't require tools, or firm steel ones (like the ones Fractal Design employs) that use screws but also feel secure as a result. Enter a third way: BitFenix's trays actually separate about a half inch, then close around the drive. These are really the best of both worlds; they feel secure while being toolless, and it's a very slick bit of engineering. You'll have to screw 2.5" drives into the trays still, but 3.5" drives go in easy. Meanwhile, the toolless clamps on the 5.25" drive bays are the standard BitFenix ones and get the job done nicely.

Lining up the power supply is easy enough, but if you're building a multi-GPU system the space for the cards is going to feel cramped. If I'd planned things a little more carefully I might have been able to do a better job of routing the power leads for the two 580s, but you can see in the photo above that we're really working with a fairly limited amount of space. If you put a high performance system in the Ronin, it's going to look and feel full.

That problem gets compounded with cabling. There's a limited amount of space to route cables, and the hole for the AUX 12V line above the motherboard is just too small for the lead. Recognizing that I'm unusually daft when it comes to clean cabling jobs, it should nonetheless be evident that the reduced dimensions of the BitFenix Ronin will make it extremely difficult to do a clean build if you're installing a high performance system. Thankfully there's enough space behind the motherboard tray that getting the rear panel slotted back on wasn't too difficult, but I have to wonder if there wouldn't have been some way to make organizing cabling a bit easier.

In and Around the BitFenix Ronin Testing Methodology
Comments Locked

30 Comments

View All Comments

  • kmmatney - Tuesday, July 23, 2013 - link

    I agree. I have a factory overclocked video card, and a "reasonably" overclocked i5, and I get plenty of cooling with a single, slow 120mm fan. While my case just has 2 120mm fans, I only use one, and keep the other unused for a spare (and to keep the system extremely quiet). I will say the price is a little high for this case, though. I think anyone buying this case would be using a single video card, so it would be more useful to test with that.
  • twtech - Monday, July 22, 2013 - link

    As soon as I saw what the inside of it looked like, I knew the cooling was going to suffer. There's no room for airflow. I wonder what the thermals would be like with just one graphics card.
  • DanNeely - Monday, July 22, 2013 - link

    The standard test is done with a single 560. Only the full fat has dual GPUs (580s).
  • GprophetB - Monday, July 22, 2013 - link

    THE BOWL IS BACK
  • HisDivineOrder - Monday, July 22, 2013 - link

    This is them creating a slightly more expensive case to sell the other cases. They make this product to hit those people who look at $99 or greater cases. Then anyone who reads a review sees they should go back to the more prevalent, cheaper cases, which they do.

    It's like advertisement for the entire brand because everytime someone goes to read about this product as it's in the running, they're going to see someone saying, "Hey, go check out Shinobi instead."

    Bam, Shinobi sells. It's savvy.
  • fluxtatic - Tuesday, July 23, 2013 - link

    Reminds me of some of the Dell Optiplexes at work. That's not a good thing.
  • ShieTar - Tuesday, July 23, 2013 - link

    Can anybody explain to me why Bitfenix would not include 2 140mm fans for the top slots? They do include them for the Shinobi XXL, and they do a great job of moving alot of air through the case, especially when combined with both front and bottom intakes. So why skip the 5 bucks on fan cost, and cripple the case in the process? Do they just expect everybody to buy their own fans anyways?
  • Minion4Hire - Tuesday, July 23, 2013 - link

    Dustin, I'm very confused. You're recommending the Shinobi over the Ronin solely because it's cheaper? But the Shinobi's thermal performance isn't really much better. It's only advantage is a 120mm side mount. If someone intends on installing two beefy graphics cards as you've done here (which you did not do in the Shinobi review) I can't imagine they're going to have a much better time in the default configuration which is otherwise identical to the Ronin.

    The Ronin looks like a prettier Shinobi. I just don't feel it's a fair performance comparison to make when you tested the Shinobi with only a single GPU. If anything I would think - assuming only one GPU - that the Ronin would perfom similarly to its spiritual predecessor.
  • samsp99 - Wednesday, July 24, 2013 - link

    Looking at the photo above, I thought it was of smoke showing the airflow in the case. Which makes me think - hey how about doing photo's of the airflow, particularly for cases with a window.
  • werver - Saturday, July 27, 2013 - link

    I was very suprised about the difference in test results of the Ronin between Anandtech.com and Computerbase.de. They write: "Bitfenix succeeded to get a very good balance between noise levels and temperature". How is such a difference possible?

Log in

Don't have an account? Sign up now